Your fleet running reports

[integrale_evo]

I was actually thinking of knocking the front down a touch tbh

[mik]

You have to. At first glance I thought it was a fuckin Hummer.

[nuttinnew]

Beany wants his camera back.

[integrale_evo]

Potato vision.

[integrale_evo]

Pretty much a 4x4

[ste]

I hadn't realised they made Venoms that big.

[240PP]

Preferred it on the M3 wheels. Please change it back.

[Sundayjumper]

Fitted passenger seat.
Bypassed passenger seat occupancy sensor (100 ohm resistor & a diode).
Bypassed both seatbelt pretensioners (2.7 ohm resistor each).
Fitted USA front bumper insert & slightly small number plate.
Fitted cheapie manual “M3” mirrors, because aero, because lightweight.

I need to source a set of rear seat belt receivers to put in the front, harnesses will be fine until the MOT comes around though. I was intending to paint the mirrors but the car has a bit of a silver / black colour scheme anyway and (IMO) they don’t look too awful, plus they were cheaper than s/h standard mirrors !

Still no steering wheel boss

Apart from that we’re very nearly ready.

13831D5B-BEC7-4B25-B753-9E551B834653.jpeg (88.38 KiB) Viewed 2544 times

[mik]

What is the advantage to removing the seatbelt pre-tensioners?

[integrale_evo]

Because they're attached to the seat along with the standard seat belt buckle and he has removed the seats and put buckets and harnesses in.

It'll light the airbag warning light which is an mot fail unless you trick it with a resistor.

[mik]

Gotcha. Thank you.

[Beany]

I tried the 'key in the lock' thing in York to see if it would put the roof down. Hey, it does.

I was impatient to get back home, so I did York to Leeds, at night, in about 7deg C, with the roof down.

That engine sounds lovely through the few tunnels on the route, I must say. Was a bit nippy though, even with the heaters on full chat.

Might have to sniff around for a wind deflector some time...

[Sundayjumper]

I am genuinely pleased that you're enjoying the BMW experience so much

[JonMad]

Fitted passenger seat.
Bypassed passenger seat occupancy sensor (100 ohm resistor & a diode).
Bypassed both seatbelt pretensioners (2.7 ohm resistor each).
Fitted USA front bumper insert & slightly small number plate.
Fitted cheapie manual “M3” mirrors, because aero, because lightweight.

I need to source a set of rear seat belt receivers to put in the front, harnesses will be fine until the MOT comes around though. I was intending to paint the mirrors but the car has a bit of a silver / black colour scheme anyway and (IMO) they don’t look too awful, plus they were cheaper than s/h standard mirrors !

Still no steering wheel boss

Apart from that we’re very nearly ready.



13831D5B-BEC7-4B25-B753-9E551B834653.jpeg

Man, you have been busy. Am liking the small front plate. And the buckets/harnesses of course.

[Sundayjumper]

BOSS

3E7AB39B-BF26-4D7C-8332-86DD8B8AF0AE.jpeg (114.55 KiB) Viewed 2365 times

[Sundayjumper]

Man, you have been busy.

It’s the prime benefit of being unemployed - you have a lot of spare time

[Foz]

I see the new merc GLE configurator is up, so how bad an idea would a new GLE450 be, the ML needs replaced and I like the look of this gen.

[Sundayjumper]

BOSS

157352AE-A01C-4BB7-86FA-8EC5FB3FB6B7.jpeg (104.1 KiB) Viewed 2345 times

[JonMad]

heh heh.
And that wheel

[Coaster1]