Page 5 of 6
Re: Shed thread
Posted: Fri Jun 19, 2020 1:20 pm
by integrale_evo
It worked out that the space between the racking at the end and the side of the shed is perfect for a stack of bmw e36 spec 17s with a stack of bare 17in wheels next to it
Now I have the basics organised the rest is starting to clear naturally as I can get to and see where to put āstuffā
Re: Shed thread
Posted: Sat Jun 20, 2020 6:43 pm
by integrale_evo
Iāve spent several hours this afternoon trying to get a wire fishing line down the conduit the existing electrical supply runs down.
Itās about 20 meters but canāt get more than about 8 meters starting at the shed end, even less starting at the house end. Iām assuming itās just catching under the cable and getting tangled rather than the conduit being collapsed or blocked.
Iād really like to run a second wire through, especially as I might end up running a supply for a summer house off the shed at some point, and would massively cut down the amount of digging I would have to do!
Any other ideas?
The only other thing I could do would be to use the existing cable to pull through the line or the line to then attach some cable to to pull back through.
I donāt have enough cable to do two fresh runs, and donāt want to get stuck and end up with no power up there!
Re: Shed thread
Posted: Sat Jun 20, 2020 8:04 pm
by John
Tie the fishing line to a ferret.
Re: Shed thread
Posted: Sat Jun 20, 2020 8:26 pm
by integrale_evo
I believe a well trained woodlouse would be a more appropriate size
Re: Shed thread
Posted: Sat Jun 20, 2020 8:34 pm
by duncs500
Carrier bag and a compressor? Seen draw cords run like that many a time and it always seems to work.
Re: Shed thread
Posted: Sat Jun 20, 2020 8:38 pm
by V8Granite
integrale_evo wrote: Sat Jun 20, 2020 8:26 pm
I believe a well trained woodlouse would be a more appropriate size
I had to run a new cat5 cable to a gas compressor and used the old cat 5 as a sacrificial line. Just use the other wire, they are horrible things to do and cable is cheaper than all the energy you will burn by swearing.
Dave!
Re: Shed thread
Posted: Sat Jun 20, 2020 10:20 pm
by jamcg
integrale_evo wrote: Sat Jun 20, 2020 6:43 pm
Iāve spent several hours this afternoon trying to get a wire fishing line down the conduit the existing electrical supply runs down.
Itās about 20 meters but canāt get more than about 8 meters starting at the shed end, even less starting at the house end. Iām assuming itās just catching under the cable and getting tangled rather than the conduit being collapsed or blocked.
Iād really like to run a second wire through, especially as I might end up running a supply for a summer house off the shed at some point, and would massively cut down the amount of digging I would have to do!
Any other ideas?
The only other thing I could do would be to use the existing cable to pull through the line or the line to then attach some cable to to pull back through.
I donāt have enough cable to do two fresh runs, and donāt want to get stuck and end up with no power up there!
Buy a set of actual cable rods?
Re: Shed thread
Posted: Sat Jun 20, 2020 10:47 pm
by integrale_evo
Didnāt think the rod style would be flexible enough to get round the 90 degree bends at the ends, so got one of the nylon ones with the springy end hoping it would find its way down as there only a single bit of twin and earth running through.
Re: Shed thread
Posted: Sat Jun 20, 2020 11:15 pm
by Rich B
I like the compressor/bag idea, but otherwise - using the old cable is about the only chance you have - just make sure the new cables are attached SECURELY!!
Re: Shed thread
Posted: Sat Jun 20, 2020 11:33 pm
by integrale_evo
Yeah, I think itās the best option. Also need to make sure the cable I have is long enough before I start.
Would be nice to get a bit of cat5 down it too but that might be a bit too much.
Re: Shed thread
Posted: Sat Jun 20, 2020 11:57 pm
by Mito Man
Cat 5 you can just make a tiny slit a few inches deep in the ground and stick it in there.
Re: Shed thread
Posted: Tue Jun 23, 2020 2:49 am
by integrale_evo
Second reel of power cable bought, and a 100m reel of cat6 and a terminal kit.
Next step will be to disconnect the ends of the existing cable and give it a pull to make sure it moves and the existing conduit isnāt blocked or collapsed. Maybe should have done that before buying more cable...
The mrs found some photos from shortly after they moved in and thereās so much rubble and hardcore under the drive it would be a monumental effort to dig a new channel.
If I can get it to the shed itās then a piece of cake to run it out the other end and up the garden at a later date
Re: Shed thread
Posted: Sat Aug 01, 2020 5:15 pm
by Mito Man
Finally put some time into this, we pretty much stopped work as lockdown ended.
Roofing done, tedious trim done, cladding all done - just needs a gutter and it would be nice to cover the osb under the front overhang at some point. The waney edge cladding stops halfway as thereās pigeon Sputniks going on those 2 walls.
Thought it would be cool to rig some lines and see if we can get grapes hanging over the underhangs - saw people doing it in Italy.
Needs some doors now. Might see if I can paint the floor tomorrow.
Re: Shed thread
Posted: Sun Aug 02, 2020 12:31 pm
by Mito Man
Floor all done, cheapest available paint was āfrigate greyā and it looks pretty nice. Will have to see how it holds up but for Ā£37 and an hours job I canāt complain.
Re: Shed thread
Posted: Sun Aug 02, 2020 1:43 pm
by duncs500
Looks alright, how did you prep the surface?
Re: Shed thread
Posted: Sun Aug 02, 2020 1:47 pm
by mik
How big is that then? Inside dimensions look similar to what I fancy - was thinking around 4x6m?
Re: Shed thread
Posted: Sun Aug 02, 2020 2:03 pm
by Mito Man
PVA diluted with water in a 1:4 ratio roughly to prep. Only put one coat of paint down as Iām hoping the PVA acts as a primer - Screwfix only had one tin of paint anyway and canāt order more in.
Internal dimensions are 5x8m
Re: Shed thread
Posted: Sun Aug 02, 2020 2:30 pm
by duncs500
Mito Man wrote: Sun Aug 02, 2020 2:03 pm
PVA diluted with water in a 1:4 ratio roughly to prep. Only put one coat of paint down as Iām hoping the PVA acts as a primer - Screwfix only had one tin of paint anyway and canāt order more in.
Internal dimensions are 5x8m
Was it dusty or pretty clean before hand? I'll be interested to see how it holds up.
Re: Shed thread
Posted: Sun Aug 02, 2020 2:42 pm
by Mito Man
Really dusty, the PVA actually did a good job of sealing the floor as it gave off no more dust after that. The only bad thing with it is that it never seemed to fully cure so wet tyres or shoes would stick/feel tacky walking on it.
Re: Shed thread
Posted: Sun Aug 02, 2020 6:13 pm
by duncs500
What's that? The PVA or the paint? Surely the PVA staying tacky is no bad thing in terms of the paint sticking?
Hopefully it works, I might just copy you if it does!
